Patch for Slackware 14.0 guest on a Linux-Vserver host
========================================================
by Roberto Puzzanghera - http://notes.sagredo.eu
version: 2012.09.29
========================================================


diff -urNB rc.d-original/rc.0 rc.d/rc.0
--- rc.d-original/rc.0	2012-08-15 01:03:12.000000000 +0200
+++ rc.d/rc.0	2012-09-29 15:23:23.347807225 +0200
@@ -37,22 +37,6 @@
 		;;
 esac
 
-# Save the system time to the hardware clock using hwclock --systohc.
-if [ -x /sbin/hwclock ]; then
-  # Check for a broken motherboard RTC clock (where ioports for rtc are
-  # unknown) to prevent hwclock causing a hang:
-  if ! grep -q -w rtc /proc/ioports ; then
-    CLOCK_OPT="--directisa"
-  fi
-  if grep -q "^UTC" /etc/hardwareclock 2> /dev/null ; then
-    echo "Saving system time to the hardware clock (UTC)."
-    /sbin/hwclock $CLOCK_OPT --utc --systohc
-  else
-    echo "Saving system time to the hardware clock (localtime)."
-    /sbin/hwclock  $CLOCK_OPT --localtime --systohc
-  fi
-fi
-
 # Run any local shutdown scripts:
 if [ -x /etc/rc.d/rc.local_shutdown ]; then
   /etc/rc.d/rc.local_shutdown stop
@@ -98,32 +82,6 @@
   sh /etc/rc.d/rc.messagebus stop
 fi
 
-# Kill any processes (typically gam) that would otherwise prevent
-# unmounting NFS volumes:
-unset FUSER_DELAY
-for dir in $(/bin/mount | grep 'type nfs' | cut -d ' ' -f 3 ) ; do
-  echo "Killing processes holding NFS mount $dir open..."
-  # Background this to prevent fuser from also blocking shutdown:
-  /usr/bin/fuser -k -m $dir &
-  FUSER_DELAY=5
-done
-# If fuser was run, let it have some delay:
-if [ ! -z "$FUSER_DELAY" ]; then
-  sleep $FUSER_DELAY
-fi
-
-# Unmount any NFS, SMB, or CIFS filesystems:
-echo "Unmounting remote filesystems."
-/bin/umount -v -a -l -f -r -t nfs,smbfs,cifs
-
-# Try to shut down pppd:
-PS="$(ps ax)"
-if echo "$PS" | /bin/grep -q -w pppd ; then
-  if [ -x /usr/sbin/ppp-off ]; then
-    /usr/sbin/ppp-off
-  fi
-fi
-
 # Shut down YP services:
 if [ -x /etc/rc.d/rc.yp ]; then
   if grep -wq stop /etc/rc.d/rc.yp ; then
@@ -131,45 +89,11 @@
   fi
 fi
 
-# Bring down the networking system, but first make sure that this
-# isn't a diskless client with the / partition mounted via NFS:
-if ! /bin/mount | /bin/grep -q 'on / type nfs' ; then
-  if [ -x /etc/rc.d/rc.inet1 ]; then
-    . /etc/rc.d/rc.inet1 stop
-  fi
-fi
-
-# In case dhcpcd might have been manually started on the command line,
-# look for the .pid file, and shut dhcpcd down if it's found:
-if /bin/ls /etc/dhcpc/*.pid 1> /dev/null 2> /dev/null ; then
-  /sbin/dhcpcd -k 1> /dev/null 2> /dev/null
-  # A little time for /etc/resolv.conf and/or other files to
-  # restore themselves.
-  sleep 2
-fi
-
-# Shut down PCMCIA devices:
-if [ -x /etc/rc.d/rc.pcmcia ]; then
-  . /etc/rc.d/rc.pcmcia stop
-  # The cards might need a little extra time here to deactivate:
-  /bin/sleep 5
-fi
-
 # Turn off process accounting:
 if [ -x /sbin/accton -a -r /var/log/pacct ]; then
   /sbin/accton off
 fi
 
-# Terminate acpid before syslog:
-if [ -x /etc/rc.d/rc.acpid -a -r /var/run/acpid.pid ]; then # quit
-  . /etc/rc.d/rc.acpid stop
-fi
-
-# Stop udev:
-if [ -x /etc/rc.d/rc.udev ]; then
-  sh /etc/rc.d/rc.udev force-stop
-fi
-
 # Kill all remaining processes.
 if [ ! "$1" = "fast" ]; then
   echo "Sending all processes the SIGTERM signal."
@@ -187,16 +111,6 @@
   fi
 fi
 
-# Carry a random seed between reboots.
-echo "Saving random seed from /dev/urandom in /etc/random-seed."
-# Use the pool size from /proc, or 512 bytes:
-if [ -r /proc/sys/kernel/random/poolsize ]; then
-  /bin/dd if=/dev/urandom of=/etc/random-seed count=1 bs=$(cat /proc/sys/kernel/random/poolsize) 2> /dev/null
-else
-  /bin/dd if=/dev/urandom of=/etc/random-seed count=1 bs=512 2> /dev/null
-fi
-/bin/chmod 600 /etc/random-seed
-
 # Before unmounting file systems write a reboot or halt record to wtmp.
 $command -w
 
@@ -205,17 +119,6 @@
   rm -f /var/lock/subsys/*
 fi
 
-# Turn off swap:
-echo "Turning off swap."
-/sbin/swapoff -a
-/bin/sync
-
-echo "Unmounting local file systems."
-/bin/umount -v -a -t no,proc,sysfs
-
-echo "Remounting root filesystem read-only."
-/bin/mount -v -n -o remount,ro /
-
 # This never hurts:
 /bin/sync
 
@@ -240,45 +143,10 @@
   done
 fi
 
-# Deactivate LVM volume groups:
-if [ -r /etc/lvmtab -o -d /etc/lvm/backup ]; then
-  echo "Deactivating LVM volume groups:"
-  /sbin/vgchange -an --ignorelockingfailure
-fi
-
 # This never hurts again (especially since root-on-LVM always fails
 # to deactivate the / logical volume...  but at least it was
 # remounted as read-only first)
 /bin/sync
 
-# sleep 3 fixes problems with some hard drives that don't
-# otherwise finish syncing before reboot or poweroff
-/bin/sleep 3
-
 # This is to ensure all processes have completed on SMP machines:
 wait
-
-if [ -x /sbin/genpowerd ]; then
-  # See if this is a powerfail situation:
-  if /bin/egrep -q "FAIL|SCRAM" /etc/upsstatus 2> /dev/null ; then
-    # Signal UPS to shut off the inverter:
-    /sbin/genpowerd -k
-    if [ ! $? = 0 ]; then
-      echo
-      echo "There was an error signaling the UPS."
-      echo "Perhaps you need to edit /etc/genpowerd.conf to configure"
-      echo "the serial line and UPS type."
-      # Wasting 15 seconds of precious power:
-      /bin/sleep 15
-    fi
-  fi
-fi
-
-# Now halt (poweroff with APM or ACPI enabled kernels) or reboot.
-if [ "$command" = "reboot" ]; then
-  echo "Rebooting."
-  /sbin/reboot
-else
-  /sbin/poweroff
-fi
-
diff -urNB rc.d-original/rc.6 rc.d/rc.6
--- rc.d-original/rc.6	2012-08-15 01:03:12.000000000 +0200
+++ rc.d/rc.6	2012-09-29 15:23:23.363807355 +0200
@@ -37,22 +37,6 @@
 		;;
 esac
 
-# Save the system time to the hardware clock using hwclock --systohc.
-if [ -x /sbin/hwclock ]; then
-  # Check for a broken motherboard RTC clock (where ioports for rtc are
-  # unknown) to prevent hwclock causing a hang:
-  if ! grep -q -w rtc /proc/ioports ; then
-    CLOCK_OPT="--directisa"
-  fi
-  if grep -q "^UTC" /etc/hardwareclock 2> /dev/null ; then
-    echo "Saving system time to the hardware clock (UTC)."
-    /sbin/hwclock $CLOCK_OPT --utc --systohc
-  else
-    echo "Saving system time to the hardware clock (localtime)."
-    /sbin/hwclock  $CLOCK_OPT --localtime --systohc
-  fi
-fi
-
 # Run any local shutdown scripts:
 if [ -x /etc/rc.d/rc.local_shutdown ]; then
   /etc/rc.d/rc.local_shutdown stop
@@ -98,32 +82,6 @@
   sh /etc/rc.d/rc.messagebus stop
 fi
 
-# Kill any processes (typically gam) that would otherwise prevent
-# unmounting NFS volumes:
-unset FUSER_DELAY
-for dir in $(/bin/mount | grep 'type nfs' | cut -d ' ' -f 3 ) ; do
-  echo "Killing processes holding NFS mount $dir open..."
-  # Background this to prevent fuser from also blocking shutdown:
-  /usr/bin/fuser -k -m $dir &
-  FUSER_DELAY=5
-done
-# If fuser was run, let it have some delay:
-if [ ! -z "$FUSER_DELAY" ]; then
-  sleep $FUSER_DELAY
-fi
-
-# Unmount any NFS, SMB, or CIFS filesystems:
-echo "Unmounting remote filesystems."
-/bin/umount -v -a -l -f -r -t nfs,smbfs,cifs
-
-# Try to shut down pppd:
-PS="$(ps ax)"
-if echo "$PS" | /bin/grep -q -w pppd ; then
-  if [ -x /usr/sbin/ppp-off ]; then
-    /usr/sbin/ppp-off
-  fi
-fi
-
 # Shut down YP services:
 if [ -x /etc/rc.d/rc.yp ]; then
   if grep -wq stop /etc/rc.d/rc.yp ; then
@@ -131,45 +89,11 @@
   fi
 fi
 
-# Bring down the networking system, but first make sure that this
-# isn't a diskless client with the / partition mounted via NFS:
-if ! /bin/mount | /bin/grep -q 'on / type nfs' ; then
-  if [ -x /etc/rc.d/rc.inet1 ]; then
-    . /etc/rc.d/rc.inet1 stop
-  fi
-fi
-
-# In case dhcpcd might have been manually started on the command line,
-# look for the .pid file, and shut dhcpcd down if it's found:
-if /bin/ls /etc/dhcpc/*.pid 1> /dev/null 2> /dev/null ; then
-  /sbin/dhcpcd -k 1> /dev/null 2> /dev/null
-  # A little time for /etc/resolv.conf and/or other files to
-  # restore themselves.
-  sleep 2
-fi
-
-# Shut down PCMCIA devices:
-if [ -x /etc/rc.d/rc.pcmcia ]; then
-  . /etc/rc.d/rc.pcmcia stop
-  # The cards might need a little extra time here to deactivate:
-  /bin/sleep 5
-fi
-
 # Turn off process accounting:
 if [ -x /sbin/accton -a -r /var/log/pacct ]; then
   /sbin/accton off
 fi
 
-# Terminate acpid before syslog:
-if [ -x /etc/rc.d/rc.acpid -a -r /var/run/acpid.pid ]; then # quit
-  . /etc/rc.d/rc.acpid stop
-fi
-
-# Stop udev:
-if [ -x /etc/rc.d/rc.udev ]; then
-  sh /etc/rc.d/rc.udev force-stop
-fi
-
 # Kill all remaining processes.
 if [ ! "$1" = "fast" ]; then
   echo "Sending all processes the SIGTERM signal."
@@ -187,16 +111,6 @@
   fi
 fi
 
-# Carry a random seed between reboots.
-echo "Saving random seed from /dev/urandom in /etc/random-seed."
-# Use the pool size from /proc, or 512 bytes:
-if [ -r /proc/sys/kernel/random/poolsize ]; then
-  /bin/dd if=/dev/urandom of=/etc/random-seed count=1 bs=$(cat /proc/sys/kernel/random/poolsize) 2> /dev/null
-else
-  /bin/dd if=/dev/urandom of=/etc/random-seed count=1 bs=512 2> /dev/null
-fi
-/bin/chmod 600 /etc/random-seed
-
 # Before unmounting file systems write a reboot or halt record to wtmp.
 $command -w
 
@@ -205,17 +119,6 @@
   rm -f /var/lock/subsys/*
 fi
 
-# Turn off swap:
-echo "Turning off swap."
-/sbin/swapoff -a
-/bin/sync
-
-echo "Unmounting local file systems."
-/bin/umount -v -a -t no,proc,sysfs
-
-echo "Remounting root filesystem read-only."
-/bin/mount -v -n -o remount,ro /
-
 # This never hurts:
 /bin/sync
 
@@ -240,45 +143,10 @@
   done
 fi
 
-# Deactivate LVM volume groups:
-if [ -r /etc/lvmtab -o -d /etc/lvm/backup ]; then
-  echo "Deactivating LVM volume groups:"
-  /sbin/vgchange -an --ignorelockingfailure
-fi
-
 # This never hurts again (especially since root-on-LVM always fails
 # to deactivate the / logical volume...  but at least it was
 # remounted as read-only first)
 /bin/sync
 
-# sleep 3 fixes problems with some hard drives that don't
-# otherwise finish syncing before reboot or poweroff
-/bin/sleep 3
-
 # This is to ensure all processes have completed on SMP machines:
 wait
-
-if [ -x /sbin/genpowerd ]; then
-  # See if this is a powerfail situation:
-  if /bin/egrep -q "FAIL|SCRAM" /etc/upsstatus 2> /dev/null ; then
-    # Signal UPS to shut off the inverter:
-    /sbin/genpowerd -k
-    if [ ! $? = 0 ]; then
-      echo
-      echo "There was an error signaling the UPS."
-      echo "Perhaps you need to edit /etc/genpowerd.conf to configure"
-      echo "the serial line and UPS type."
-      # Wasting 15 seconds of precious power:
-      /bin/sleep 15
-    fi
-  fi
-fi
-
-# Now halt (poweroff with APM or ACPI enabled kernels) or reboot.
-if [ "$command" = "reboot" ]; then
-  echo "Rebooting."
-  /sbin/reboot
-else
-  /sbin/poweroff
-fi
-
diff -urNB rc.d-original/rc.M rc.d/rc.M
--- rc.d-original/rc.M	2012-09-25 19:47:07.000000000 +0200
+++ rc.d/rc.M	2012-09-29 15:33:01.756524040 +0200
@@ -20,10 +20,6 @@
   /sbin/ldconfig &
 fi
 
-# Screen blanks after 15 minutes idle time, and powers down in one hour
-# if the kernel supports APM or ACPI power management:
-/bin/setterm -blank 15 -powersave powerdown -powerdown 60
-
 # Set the hostname.
 if [ -r /etc/HOSTNAME ]; then
   /bin/hostname $(cat /etc/HOSTNAME | cut -f1 -d .)
@@ -47,31 +43,6 @@
 # Save the contents of 'dmesg':
 /bin/dmesg -s 65536 > /var/log/dmesg
 
-# Initialize PCMCIA devices:
-#
-# NOTE: This used to be started near the top of rc.S so that PCMCIA devices
-# could be fsck'ed along with the other drives.  This had some unfortunate
-# side effects, however, since root isn't yet read-write, and /var might not
-# even be mounted the .pid files can't be correctly written in /var/run and
-# the pcmcia system can't be correctly shut down.  If you want some PCMCIA
-# partition to be mounted at boot (or when the card is inserted) then add
-# the appropriate lines to /etc/pcmcia/scsi.opts.
-#
-# Note that the stuff in /etc/pcmcia/ is only for 2.4.x kernels using
-# 16-bit PCMCIA cards (not 32-bit Cardbus cards!).  For example, with a
-# wireless card you might need to set options in /etc/pcmcia OR in
-# /etc/rc.d/rc.wireless.conf, or even in /etc/rc.d/rc.inet1.conf (with
-# extra options if needed for the encryption key, ESSID, etc.)
-#
-# Hopefully this situation will be unified in the future, but for now
-# that's how it is...
-#
-if [ -x /etc/rc.d/rc.pcmcia ]; then
-  . /etc/rc.d/rc.pcmcia start
-  # The cards might need a little extra time here to initialize.
-  sleep 5
-fi
-
 # Start the system logger.
 if [ -x /etc/rc.d/rc.syslog -a -x /usr/sbin/syslogd -a -d /var/log ]; then
   . /etc/rc.d/rc.syslog start
@@ -83,40 +54,11 @@
   /usr/bin/fc-cache -f &
 fi
 
-# Run rc.udev again.  This will start udev if it is not already running
-# (for example, upon return from runlevel 1), otherwise it will trigger it
-# to look for device changes and to generate persistent rules if needed.
-if grep -wq sysfs /proc/mounts && grep -q tmpfs /proc/filesystems ; then
-  if ! grep -wq nohotplug /proc/cmdline ; then
-    if [ -x /etc/rc.d/rc.udev ]; then
-      /bin/sh /etc/rc.d/rc.udev start
-    fi
-  fi
-fi
-
-# Initialize the networking hardware.
-if [ -x /etc/rc.d/rc.inet1 ]; then
-  . /etc/rc.d/rc.inet1
-fi
-
-# Look for additional USB/SCSI/IEEE1394/etc devices on multiple LUNs:
-if [ -x /etc/rc.d/rc.scanluns ]; then
-  . /etc/rc.d/rc.scanluns
-fi
-
 # Start networking daemons:
 if [ -x /etc/rc.d/rc.inet2 ]; then
   . /etc/rc.d/rc.inet2
 fi
 
-# Mount any additional filesystem types that haven't already been mounted:
-mount -a -v 2> /dev/null | grep -v "already mounted"
-
-# Start the Control Script for automounter:
-if [ -x /etc/rc.d/rc.autofs ]; then
-  sh /etc/rc.d/rc.autofs start
-fi
-
 # Start the Network Time Protocol daemon:
 if [ -x /etc/rc.d/rc.ntpd ]; then
   sh /etc/rc.d/rc.ntpd start
@@ -135,17 +77,6 @@
 chmod 755 / 2> /dev/null
 chmod 1777 /tmp /var/tmp
 
-# Start APM or ACPI daemon.
-# If APM is enabled in the kernel, start apmd:
-if [ -e /proc/apm ]; then
-  if [ -x /usr/sbin/apmd ]; then
-    echo "Starting APM daemon:  /usr/sbin/apmd"
-    /usr/sbin/apmd
-  fi
-elif [ -x /etc/rc.d/rc.acpid ]; then # otherwise, start acpid:
-  . /etc/rc.d/rc.acpid start
-fi
-
 # Update any existing icon cache files:
 if find /usr/share/icons 2> /dev/null | grep -q icon-theme.cache ; then
   for theme_dir in /usr/share/icons/* ; do
@@ -183,18 +114,6 @@
   sh /etc/rc.d/rc.hald start
 fi
 
-# Start Bluetooth:
-if [ -x /etc/rc.d/rc.bluetooth ]; then
-  sh /etc/rc.d/rc.bluetooth start
-fi
-
-# Start wicd or networkmanager:
-if [ -x /etc/rc.d/rc.wicd -a -x /usr/sbin/wicd ]; then
-  sh /etc/rc.d/rc.wicd start
-elif [ -x /etc/rc.d/rc.networkmanager ]; then
-  sh /etc/rc.d/rc.networkmanager start
-fi
-
 # These GTK+/pango files need to be kept up to date for
 # proper input method, pixbuf loaders, and font support.
 if [ -x /usr/bin/update-gtk-immodules ]; then
@@ -207,60 +126,11 @@
   /usr/bin/update-pango-querymodules --verbose
 fi
 
-# Start dnsmasq, a simple DHCP/DNS server:
-if [ -x /etc/rc.d/rc.dnsmasq ]; then
-  /etc/rc.d/rc.dnsmasq start
-fi
-
 # Start snmpd:
 if [ -x /etc/rc.d/rc.snmpd ]; then
   /etc/rc.d/rc.snmpd start
 fi
 
-# Start the print spooling system.  This will usually be LPRng (lpd) or CUPS.
-if [ -x /etc/rc.d/rc.cups ]; then
-  # Start CUPS:
-  /etc/rc.d/rc.cups start
-elif [ -x /etc/rc.d/rc.lprng ]; then
-  # Start LPRng (lpd):
-  . /etc/rc.d/rc.lprng start
-fi
-
-# Start netatalk. (a file/print server for Macs using Appletalk)
-if [ -x /etc/rc.d/rc.atalk ]; then
-  /etc/rc.d/rc.atalk start
-fi
-
-# Start smartd, which monitors the status of S.M.A.R.T. compatible
-# hard drives and reports any problems.  Note some devices (which aren't
-# smart, I guess ;) will hang if probed by smartd, so it's commented out
-# by default.
-#if [ -x /usr/sbin/smartd ]; then
-#  /usr/sbin/smartd
-#fi
-
-# If we're using udev, make /dev/cdrom and any other optical drive symlinks
-# if some udev rule hasn't made them already:
-if grep -wq sysfs /proc/mounts && grep -q tmpfs /proc/filesystems; then
-  if ! grep -wq nohotplug /proc/cmdline ; then
-    if [ -x /lib/udev/rc.optical-symlinks -a -x /etc/rc.d/rc.udev ]; then
-      /bin/sh /lib/udev/rc.optical-symlinks
-    fi
-  fi
-fi
-
-# Monitor the UPS with genpowerd.
-# To use this, uncomment this section and edit your settings in
-# /etc/genpowerd.conf (serial device, UPS type, etc).  For more information,
-# see "man genpowerd" or the extensive documentation in the
-# /usr/doc/genpower-*/ directory.
-# You'll also need to configure a similar block in /etc/rc.d/rc.6 if you want
-# support for stopping the UPS's inverter after the machine halts.
-#if [ -x /sbin/genpowerd ]; then
-#  echo "Starting genpowerd daemon..."
-#  /sbin/genpowerd
-#fi
-
 # Turn on process accounting.  To enable process accounting, make sure the
 # option for BSD process accounting is enabled in your kernel, and then
 # create the file /var/log/pacct (touch /var/log/pacct).  By default, process
@@ -325,11 +195,6 @@
   . /etc/rc.d/rc.sendmail start
 fi
 
-# Load ALSA (sound) defaults:
-if [ -x /etc/rc.d/rc.alsa ]; then
-  . /etc/rc.d/rc.alsa
-fi
-
 # Load a custom screen font if the user has an rc.font script.
 if [ -x /etc/rc.d/rc.font ]; then
   . /etc/rc.d/rc.font
@@ -361,11 +226,6 @@
   . /etc/rc.d/rc.samba start
 fi
 
-# Start the GPM mouse server:
-if [ -x /etc/rc.d/rc.gpm ]; then
-  . /etc/rc.d/rc.gpm start
-fi
-
 # If there are SystemV init scripts for this runlevel, run them.
 if [ -x /etc/rc.d/rc.sysvinit ]; then
   . /etc/rc.d/rc.sysvinit
diff -urNB rc.d-original/rc.S rc.d/rc.S
--- rc.d-original/rc.S	2012-09-13 21:38:34.000000000 +0200
+++ rc.d/rc.S	2012-09-29 15:23:23.391807582 +0200
@@ -48,16 +48,6 @@
   fi
 fi
 
-# Mount Control Groups filesystem interface:
-if grep -wq cgroup /proc/filesystems ; then
-  if [ -d /sys/fs/cgroup ]; then
-    mount -t cgroup cgroup /sys/fs/cgroup
-  else
-    mkdir -p /dev/cgroup
-    mount -t cgroup cgroup /dev/cgroup
-  fi
-fi
-
 # Initialize the Logical Volume Manager.
 # This won't start unless we find /etc/lvmtab (LVM1) or
 # /etc/lvm/backup/ (LVM2).  This is created by /sbin/vgscan, so to
diff -urNB rc.d-original/rc.inet2 rc.d/rc.inet2
--- rc.d-original/rc.inet2	2012-08-15 00:53:35.000000000 +0200
+++ rc.d/rc.inet2	2012-09-29 15:23:23.403807679 +0200
@@ -16,26 +16,6 @@
 # At this point, we are ready to talk to The World...
 
 
-# Mount remote (NFS) filesystems:
-if cat /etc/fstab | grep -v '^#' | grep -w nfs 1> /dev/null 2> /dev/null ; then
-  # Start rpc.portmap, /sbin/rpc.lockd, and /sbin/rpc.statd if we find NFS
-  # volumes defined in /etc/fstab since these will need to be running in order
-  # to mount them.  If they are not running, attempting to mount an NFS
-  # partition will cause mount to hang, or at least result in unreliable
-  # operation.  Keep this in mind if you plan to mount unlisted NFS
-  # partitions... 
-  # If you have uncommented NFS partitions in your /etc/fstab, rc.rpc is run
-  # whether it is set as executable or not.  If you don't want to run it,
-  # comment the NFS partitions out in /etc/fstab or erase/rename rc.rpc.
-  if [ -r /etc/rc.d/rc.rpc ]; then
-    sh /etc/rc.d/rc.rpc start
-  fi
-  echo "Mounting remote (NFS) file systems:  /sbin/mount -a -t nfs"
-  /sbin/mount -a -t nfs          # This may be our /usr runtime!
-  # Show the mounted volumes:
-  /sbin/mount -v -t nfs
-fi
-
 # If /etc/rc.d/rc.rpc is executable, run it to load rpc.portmap, rpc.lockd,
 # and rpc.statd.  This might be needed to mount NFS partitions that are not
 # listed in /etc/fstab.  Starting this twice won't hurt as the script will
@@ -44,23 +24,6 @@
   sh /etc/rc.d/rc.rpc start
 fi
 
-# Mount remote CIFS filesystems.  Note that where possible, using CIFS is
-# preferred over SMBFS.  SMBFS is no longer actively maintained.
-if cat /etc/fstab | grep -v '^#' | grep -w cifs 1> /dev/null 2> /dev/null ; then
-  echo "Mounting remote CIFS file systems:  /sbin/mount -a -t cifs"
-  /sbin/mount -a -t cifs
-  # Show the mounted volumes:
-  /sbin/mount -v -t cifs
-fi
-
-# Mount remote SMB filesystems:
-if cat /etc/fstab | grep -v '^#' | grep -w smbfs 1> /dev/null 2> /dev/null ; then
-  echo "Mounting remote SMBFS file systems:  /sbin/mount -a -t smbfs"
-  /sbin/mount -a -t smbfs
-  # Show the mounted volumes:
-  /sbin/mount -v -t smbfs
-fi
-
 # Start the system logger if it is not already running (maybe because /usr
 # is on a network partition).
 if [ -x /etc/rc.d/rc.syslog -a -d /var/log -a ! -r /var/run/syslogd.pid ]; then
diff -urNB rc.d-original/rc.syslog rc.d/rc.syslog
--- rc.d-original/rc.syslog	2010-10-21 01:03:54.000000000 +0200
+++ rc.d/rc.syslog	2012-09-29 15:23:23.419807809 +0200
@@ -5,8 +5,9 @@
 
 syslogd_start() {
   if [ -x /usr/sbin/syslogd -a -x /usr/sbin/klogd ]; then
-    echo -n "Starting sysklogd daemons:  "
-    echo -n "/usr/sbin/syslogd "
+#    echo -n "Starting sysklogd daemons:  "
+    echo -n "Starting /usr/sbin/syslogd "
+    echo
     /usr/sbin/syslogd
     # prevent syslogd/klogd race condition on SMP kernels
     if ps acx | grep -q udevd ; then
@@ -16,10 +17,10 @@
     else
       sleep 1
     fi
-    echo "/usr/sbin/klogd -c 3 -x"
+#    echo "/usr/sbin/klogd -c 3 -x"
     # '-c 3' = display level 'error' or higher messages on console
     # '-x' = turn off broken EIP translation
-    /usr/sbin/klogd -c 3 -x
+#    /usr/sbin/klogd -c 3 -x
   fi
 }